| |
|
|
|
|
|
| |
Step
1: Connect the Sipura SPA-2000 to your Broadband connection |
|
| |
Step
2: Verify your IP address and Initial SPA-2000 Configuration |
|
| |
Step
3: Install SPA-2000 software version 2.0.11(g) |
|
| |
Step
4: Configure your Sipura SPA-2000 |
|
| |
Step
5: Start using your SPA-2000 with Phone4internet Calling
Accounts |
|
| |
| Step 1: Connect the Sipura SPA-2000
to your Broadband connection |
| |
| |
1. Connect your power
and a RJ-45 Ethernet cable to the left side of the Sipura
SPA-2000.
2. Connect up to two regular analog telephones to the
right side of the Sipura SPA-2000, using standard RJ-11
telephone cables.
|
|
| |
| |
|
|
| Step 2: Verify your IP address and
Initial SPA-2000 Configuration |
| |
| |
1. To configure the
SPA-2000, you should have the following information:
- IP address, Sub-Net and Gateway addresses or DHCP
availability
- deltathree User IDs and passwords
2. Use a touch tone telephone attached to Port 1 or
Port 2 of the SPA-2000 and press the star key four times
(****) to enter the Sipura Configuration menu.
Please use the table below for options and responses
to the information you may use to configure the SPA-2000: |
|
| |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| |
|
Action |
|
|
|
Menu Choice |
|
|
|
User Input |
|
|
|
Notes |
|
|
| |
| |
|
Enter IVR Menu |
|
|
|
* * * * |
|
|
|
None |
|
|
|
None. Ignore SIT or other
tones until you hear, “Sipura configuration menu.
Please enter option followed by the pound key or
hang-up to exit.” |
|
|
| |
| |
|
Check DHCP |
|
|
|
100# |
|
|
|
None |
|
|
|
IVR will announce if DHCP
in enabled or disabled. |
|
|
| |
| |
|
Enable/Disable DHCP |
|
|
|
101# |
|
|
|
Enter 1 to enable
Enter 0 to disable |
|
|
|
|
|
|
| |
| |
|
Check IP Address |
|
|
|
110# |
|
|
|
None |
|
|
|
IVR will announce current
IP Address of SPA. |
|
|
| |
| |
|
Set Static IP Address |
|
|
|
111# |
|
|
|
Enter IP address using numbers
on the telephone key pad. Use the *(star) key when
entering a decimal point. |
|
|
|
DHCP must be “Disabled” otherwise
you will hear, “Invalid Option,” if you try to set
this value. |
|
|
| |
| |
|
Check Network Mask |
|
|
|
120# |
|
|
|
None |
|
|
|
IVR will announce the current
network mask of SPA. |
|
|
| |
| |
|
Set Network Mask |
|
|
|
121# |
|
|
|
Enter value using numbers
on the telephone key pad. Use the * (star) key when
entering a decimal point. |
|
|
|
DHCP must be “Disabled” otherwise
you will hear, “Invalid Option,” if you try to set
this value. |
|
|
| |
| |
|
Check Static Gateway IP Address |
|
|
|
130# |
|
|
|
None |
|
|
|
IVR will announce the current
gateway IP address of SPA. |
|
|
| |
| |
|
Set Static Gateway IP Address |
|
|
|
131# |
|
|
|
Enter IP address using numbers
on the telephone key pad. Use the *(star) key when
entering a decimal point. |
|
|
|
DHCP must be “Disabled” otherwise
you will hear, “Invalid Option,” if you try to set
this value. |
|
|
| |
|
| |
| |
|
|
| |
| Step 3: Install SPA-2000 software
version 2.0.11(g) |
| |
| |
1. Check the software version
that the SPA is running:
- Open a session to the SPA by typing: http://(SPA's
IP address)
- Click on the “Info” tab, then go to the “Product Information”
section, and find the “Software Version.”
If the SPA has software version 2.0.11(g), continue
to STEP 4.
If the SPA does not have software version 2.0.11(g), follow
the instructions below.
2. Click here to install the software.
Follow the prompts to complete installation.
Make sure to install the software on a computer that
is connected to the same network as the SPA-2000. Please
do not unplug the SPA until the status light stops
blinking and the software installation is complete. This
process can take several minutes.
When the software has been installed on the SPA, you will
see a popup window with the message “Your SPA has been
successfully upgraded to the version show below: 2.0.11(g)”
If the upgrade fails, verify that your SPA is properly
configured on your home network and check your ISP connectivity.
|
|
| |
| |
|
|
| Step 4: Configure your Sipura SPA-2000 |
| |
| |
1. Open a session to the
SPA by typing: http://(SPA's IP address)
2. Click “Admin Login” at the bottom or upper right hand
corner of the configuration page.
3. Click "Advanced" at the bottom or upper right hand corner
of the configuration page.
4. The browser will show a tabbed user interface. To complete
the configuration, you will enter information into fields
on the Line 1 and/or Line 2, Provisioning, and SIP tabs.
Use the Line 1 tab to configure service for Phone 1 and
the Line 2 tab to configure service for Phone 2.
- Enter the values for your configuration type into
the corresponding fields as indicated on the sample
SPA-2000 Configuration forms.
- ONLY INPUT VALUES INTO THE SPECIFIED FIELDS. DO NOT
change the values in any of the other fields.
- Click Submit All Changes
at the bottom of the web page after you fill in all
appropriate fields.
Choose between two sample SPA-2000 Configuration forms: |
|
| |
| |
a. Make Calls only
b. Make & Receive Calls
|
|
| |
a. Make Calls
only
|
|
| |
1. Click Line 1 for
phone 1 and Line 2 for phone 2 on the configuration
menu.
2. Go to Proxy and Registration
- Next to Proxy: enter
sipauth.deltathree.com
- Next to Register: enter NO
- Next to Register Expires:
enter 300
- Next to Use OB Proxy In Dialog:
enter NO
- Next to Make Call Without Reg:
enter YES
3. Go to Subscriber Information
- Next to Display Name:
enter Your name that will appear
on Caller ID, if you choose
- Next to Password: enter Your 4 digit password
- Next to Auth ID:
enter Your 8 digit Phone4internet
account number
- Next to User ID:
enter Your 8 digit Phone4internet
account number
- Next to Use Auth ID:
enter YES
4. Go to Audio Configuration
- Select the Preferred Codec:
based on the speed of your Internet connection
5. Go to Dial Plan
- Next to Dial Plan:
enter (*xx|[3469]11|0|00|[2-9]xxxxxx|1[2-9]xx[2-9]xxxxxxS0|xxxxxxxxxxxx.)
6. Click Provisioning on the configuration menu.
7. Go to Configuration Profile
- Change Provision Enable:
to NO
8. Click the Submit All Changes button to save your
changes. |
|
| |
| |
|
|
| |
|
|
| |
1. Click Line 1 for
phone 1 and Line 2 for phone 2 on the configuration
menu.
2. Go to NAT settings
- Change Keep Alive Enable:
to YES
3. Go to Proxy and Registration
- Next to Proxy: enter
sipauth.deltathree.com
- Change Register:
to YES
- Change Register Expires:
to 300
- Change Use OB Proxy In Dialog:
to NO
- Change Make Call Without Reg:
to YES
4. Go to Subscriber Information
- Next to Display Name:
enter Your name that will appear
on Caller ID, if you choose
- Next to Password: enter Your 4 digit password
- Next to Auth ID:
enter Your 8 digit Phone4internet
account number
- Next to User ID:
enter YourPhone4internet Inbound
Phone Number (e.g. 12125551212 for a USA number)
- Next to Use Auth ID:
enter YES
5. Go to Audio Configuration
- Select the Preferred Codec:
based on the speed of your Internet connection
6. Go to Dial Plan
- Next to Dial Plan:
enter (*xx|[3469]11|0|00|[2-9]xxxxxx|1[2-9]xx[2-9]xxxxxxS0|xxxxxxxxxxxx.)
7. Click Provisioning on the configuration menu.
8. Go to Configuration Profile
- Change Provision Enable:
to NO
9. Click SIP on the configuration menu
10. Go to NAT Support Parameters
- Next to NAT Keep Alive Intvl:
enter 45
11. Click the Submit All Changes button to save your
changes. |
|
| |
|
|
| |
| Step 5: Start using your SPA-2000
with Phone4internet Calling Accounts |
| |
| |
You are ready to make and
receive calls. Pick up the phone and start dialing. Make
sure to dial country code, area code, and the number - even
for local phone calls: e.g. USA call 1-212-555-1212. |
|
|
