  |
|
|
SIPURA SPA-2000 IVR MODE SET-UP
INSTRUCTIONS - CONFIGURATION
| |
|
|
|
|
|
| |
Step
1: Connect the Sipura SPA-2000 to your Broadband connection |
|
| |
Step
2: Verify your IP address and Initial SPA-2000 Configuration |
|
| |
Step
3: Install SPA-2000 software version 2.0.11(g) |
|
| |
Step
4: Configure your Sipura SPA-2000 |
|
| |
Step 5: Start using your SPA-2000 with Phone4internet
Calling Accounts |
|
| |
| |
Step 1: Connect the Sipura SPA-2000
to your Broadband connection |
| |
| |
1. Connect your power
and a RJ-45 Ethernet cable to the left side of the Sipura
SPA-2000.
2. Connect up to two regular analog telephones to the
right side of the Sipura SPA-2000, using standard RJ-11
telephone cables.
|
|
| |
| |
|
|
| Step 2: Verify your IP address and
Initial SPA-2000 Configuration |
| |
| |
|
|
| |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| |
|
Action |
|
|
|
Menu Choice |
|
|
|
User Input |
|
|
|
Notes |
|
|
| |
| |
|
Enter IVR Menu |
|
|
|
* * * * |
|
|
|
None |
|
|
|
None. Ignore SIT or other
tones until you hear, “Sipura configuration menu.
Please enter option followed by the pound key or
hang-up to exit.” |
|
|
| |
| |
|
Check DHCP |
|
|
|
100# |
|
|
|
None |
|
|
|
IVR will announce if DHCP
in enabled or disabled. |
|
|
| |
| |
|
Enable/Disable DHCP |
|
|
|
101# |
|
|
|
Enter 1 to enable
Enter 0 to disable |
|
|
|
|
|
|
| |
| |
|
Check IP Address |
|
|
|
110# |
|
|
|
None |
|
|
|
IVR will announce current
IP Address of SPA. |
|
|
| |
| |
|
Set Static IP Address |
|
|
|
111# |
|
|
|
Enter IP address using numbers
onthe telephone key pad. Use the *(star) key when
entering a decimal point. |
|
|
|
DHCP must be “Disabled” otherwise
you will hear, “Invalid Option,” if you try to set
this value. |
|
|
| |
| |
|
Check Network Mask |
|
|
|
120# |
|
|
|
None |
|
|
|
IVR will announce the current
network mask of SPA. |
|
|
| |
| |
|
Set Network Mask |
|
|
|
121# |
|
|
|
Enter value using numbers
on the telephone key pad. Use the * (star) key when
entering a decimal point. |
|
|
|
DHCP must be “Disabled” otherwise
you will hear, “Invalid Option,” if you try to set
this value. |
|
|
| |
| |
|
Check Static Gateway IP Address |
|
|
|
130# |
|
|
|
None |
|
|
|
IVR will announce the current
gateway IP address of SPA. |
|
|
| |
| |
|
Set Static Gateway IP Address |
|
|
|
131# |
|
|
|
Enter IP address using numbers
on the telephone key pad. Use the *(star) key when
entering a decimal point. |
|
|
|
DHCP must be “Disabled” otherwise
you will hear, “Invalid Option,” if you try to set
this value. |
|
|
| |
|
| |
| |
|
|
| |
| |
Step 3: Install SPA-2000 software
version 2.0.11(g) |
| |
| |
1. Check the software version
that the SPA is running:
- Open a session to the SPA by typing: http://(SPA's
IP address)
- Click on the “Info” tab, then go to the “Product Information”
section, and find the “Software Version.”
If the SPA has software version 2.0.11 (g), continue
to STEP 4.
If the SPA does not have software version 2.0.11 (g),
follow the instructions below.
2. Click here to install the software.
Follow the prompts to complete installation.
Make sure to install the software on a computer that
is connected to the same network as the SPA-2000. Please
do not unplug the SPA until the status light stops
blinking and the software installation is complete. This
process can take several minutes.
When the software has been installed on the SPA, you will
see a popup window with the message “Your SPA has been
successfully upgraded to the version show below: 2.0.11(g)”
If the upgrade fails, verify that your SPA is properly
configured on your home network and check your ISP connectivity.
|
|
| |
| |
|
|
| Step 4: Configure your Sipura SPA-2000 |
| |
| |
1. Open a session to the
SPA by typing: http://(SPA's IP address).
2. Click “Admin Login” at the bottom or upper right hand
corner of the configuration page.
3. Click “Advanced” at the bottom or upper right hand corner
of the configuration page.
4. The browser will show a tabbed user interface. To complete
the configuration, you will enter information into fields
on the Line 1 and/or Line 2 tabs and the Provisioning tab.
Use the Line 1 tab to configure service for Phone 1 and
the Line 2 tab to configure service for Phone 2.
- Enter the values for your configuration type into
the corresponding fields as indicated on the sample
SPA-2000 Configuration forms.
- ONLY INPUT VALUES INTO THE SPECIFIED FIELDS. DO NOT
change the values in any of the other fields.
- Click Submit All Changes
at the bottom of the web page after you fill in all
appropriate fields.
Please follow the configuration instructions below:
|
|
| |
1. Click Line 1 for
phone 1 and Line 2 for phone 2 on the configuration
menu.
2. Go to Proxy and Registration
- Next to Proxy: enter
c-ivr-devices.deltathree.com
- Next to Register: enter NO
- Next to Register Expires:
enter 300
- Next to Use OB Proxy In Dialog:
enter NO
- Next to Make Call Without Reg:
enter YES
3. Go to Subscriber Information
- Next to Display Name:
enter Your name that will appear
on Caller ID, if you choose
- Next to Password: enter Leave blank
- Next to Auth ID:
enter Leave blank
- Next to User ID:
enter Leave blank
- Next to Use Auth ID:
enter No
4. Go to Audio Configuration
- Select the Preferred Codec:
based on the speed of your Internet connection
- Next to DTMF TX Method:
enter INFO
5. Go to Dial Plan
- Next to Dial Plan:
enter (S0<:8888>)
6. Click Provisioning on the configuration menu.
7. Go to Configuration Profile
- Change Provision Enable:
to NO
8. Click the Submit All Changes button to save your
changes. |
|
| |
|
|
| |
| |
| Step 5: Start using your SPA-2000
with Phone4internet Calling Accounts |
| |
| |
You are ready to make calls.
Pick up the phone and you will hear the automated IVR prompts.
Enter your Phone4internet accoubt 8-digit User ID, 4-digit
password, and destination telephone number as instructed
by the IVR prompts to make calls. Make sure to dial country
code, area code, and the number - even for local phone calls:
e.g. USA call 1-212-666-1212. |
|
|
|
