Dial Tone Mode: Your
gateway, configured with predefined Calling Accounts,
will produce a dial tone, enabling your users to
pick up the phone and dial
the destination number
to make calls.
Step
1: Connect the Linksys PAP2 to
your Broadband internet connection
1. Connect your
power and the cable to the back side of the Linksys
.
2. Connect up to
two regular phones to the two phone ports located
in the
back side of the Linksys, using standard RJ-11 phone
cables.
Step 2: Verify
your IP address and Initial LINKSYS PAP2 Configuration
1. To configure
the LINKSYS , you should have the following information:
a.IP address,
b.SubNet and Gateway addresses or DHCP availability
c.Phone4internet User IDs and passwords
2. Use a touch tone
telephone attached to Port 1 or Port 2 of the LINKSYS
and
press the star key four times (****) to enter the
Linksys Configuration menu.
Please use the table
below for options and responses to the information
you
may use to configure the LINKSYS:
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| |
|
Action |
|
|
|
Menu Choice |
|
|
|
User Input |
|
|
|
Notes |
|
|
| |
| |
|
Enter IVR Menu |
|
|
|
* * * * |
|
|
|
None |
|
|
|
None. Ignore SIT or
other tones until you hear, “Linksys configuration
menu. Please enter option followed by the
pound key or hang-up to exit.” |
|
|
| |
| |
|
Check DHCP |
|
|
|
100# |
|
|
|
None |
|
|
|
IVR will announce if
DHCP in enabled or disabled. |
|
|
| |
| |
|
Enable/Disable DHCP |
|
|
|
101# |
|
|
|
Enter 1 to enable
Enter 0 to disable |
|
|
|
|
|
|
| |
| |
|
Check IP Address |
|
|
|
110# |
|
|
|
None |
|
|
|
IVR will announce current
IP Address of PAP2. |
|
|
| |
| |
|
Set Static IP Address |
|
|
|
111# |
|
|
|
Enter IP address using
numbers on the telephone key pad. Use the
*(star) key when entering a decimal point. |
|
|
|
DHCP must be “Disabled”
otherwise you will hear, “Invalid Option,”
if you try to set this value. |
|
|
| |
| |
|
Check Network Mask |
|
|
|
120# |
|
|
|
None |
|
|
|
IVR will announce the
current network mask of PAP2 |
|
|
| |
| |
|
Set Network Mask |
|
|
|
121# |
|
|
|
Enter value using numbers
on the telephone key pad. Use the * (star)
key when entering a decimal point. |
|
|
|
DHCP must be “Disabled”
otherwise you will hear, “Invalid Option,”
if you try to set this value. |
|
|
| |
| |
|
Check Static Gateway
IP Address |
|
|
|
130# |
|
|
|
None |
|
|
|
IVR will announce the
current gateway IP address of PAP2. |
|
|
| |
| |
|
Set Static Gateway IP
Address |
|
|
|
131# |
|
|
|
Enter IP address using
numbers on the telephone key pad. Use the
*(star) key when entering a decimal point. |
|
|
|
DHCP must be “Disabled”
otherwise you will hear, “Invalid Option,”
if you try to set this value. |
|
|
| |
TOP
Step 3: Configure your Linksys
PAP2
1. Open a session to
the PAP2 by typing: http://(PAP2's IP address)
2. Click "Admin
Login" at the bottom or upper right hand corner
of the configuration page.
3. Click "Advanced"
at the bottom or upper right hand corner of the
configuration page.
4. The browser will show
a tabbed user interface. Enter the Provisioning
Tab.
Make sure you have the
following settings configured:
Provision Enable: Yes
Resync Periodic: 60
Resync Error Retry Delay: 60
Profile Rule: http://213.137.73.74/pap2reseller-ivr.cfg
( Example )
5. Proceed to the System
Tab:
Make sure you have the following settings configured:
Primary DNS: 213.137.73.254
Secondary DNS: 208.170.171.93
6. Save your settings
by clicking the Save Settings button at the bottom
of the page.
7. After you have confirmed
that the changes were implemented,
disconnect the Linksys from the power and reconnect
it after a few seconds.
TOP
4: Start
using your Linksys PAP2 with Phone4internet Calling
Accounts
You are ready to
make and receive calls. Pick up the phone and start
dialing.
Make sure to dial country code, area code, and the
number - even for local phone
calls:
e.g. USA call 13102225555.
TOP
Charge
Your Account With Us
We will configure
your Linksys
Contact us  We
will call you back
|
